Digital / Analog Electronics Lab

The Digital / analog lab is accessible to students of all the departments. The lab is well equipped with Digital storage oscilloscope function generators, digital multimeters, general purpose ICs, etc. used in design and implementation of basic electronic circuits.

Experiments performed in the lab range from hardware design and implementation of rectifiers, analysis of transistor characteristics, comparators, synchronous and asynchronous counters,op amp applications etc.

Digital Analog Electronics Lab In-charge

Dr. Ankush Bag
Asst. Professor
Phone: 267276
EMail: ankushbag
Home Page

Digital Analog Electronics Lab Staff

List of Equipments

	Specifications: Input Bandwidth: 50 MHz Channel : 2 Max. Sample rate : 1GSa/s Display : 5.7 inch Input Impedance : 1MΩ ± 2% in Parallel with 15 pF ± 3pF Input Coupling : AC,DC,Ground Time Scale Accuracy : ± 50 ppm over 1 ms (B models only Vertical Sensitivity (range) : 2 mV/div to 10 V/div DC gain Accuracy : 10 mV/div to 10 V/div: ± 3.0% full scale Standard Ports : USB 2.0-compliant host port on front panel
	Specifications: Operating Modes : Sine, Square, Triangle, Ramp, Pulse, TTL Frequency Range : 1 Hz - 10 MHz in 7 steps Frequency accuracy : ± 0.5 % Sine wave distortion : 1 % (typical) Square wave rise and fall time : = 50 ns Input Impedence : 1Mohm Output Voltage : 20Vpp (open circuit) Pulse Duty Cycle : 15 % to 85 % var. (min width 200 ns) Frequency Counter : DC - 40 MHz
	Specifications: Three floating independent DC supply voltages DC outputs :- A: 0-30V,2Amps , B: 5V,2Amps , C: 0 ± 15V (Dual tracking )/1Amps each Constant voltage and constant current operation Adjustable current limiter
	Specifications: Bandwidth : 500 MHz Channel : 4 Display : 8.5 Inch Max Sample Rate : 4 GSa/s Function generator operating Modes : Sine ,Square ,Ramp, modulation (AM,FM,FSK) Input impedance (Vertical system analog channel) : Selectable: 1 MΩ ± 1% (14 pF), 50 Ω ± 1.5% Input impedance (Vertical system Digital channel) : 100 kΩ ± 2% at probe tip Standard Ports : Two USB 2.0 hi-speed host ports, front and rear panel
	Specifications: Frequency Range : 0.3Hz to 3MHz Operating Modes : Sine, Square, Triangle, DC Output Voltage: 10Vpp into 50Ω,Max 20Vpp open circuit Input Impedance: 50KΩ | 25pF
	Specifications: The trainer kit provides basic facilities essential for conducting experiments using TTL as well as CMOS ICs 10 TTL compatible logic input levels Four crystal generated clock output of 1 MHz, 1KHz, 100Hz,5Hz,1Hz Built in power supply 5V,12V Four seven segment displays with BCD inputs
	Specifications: Input Impedance : 3 MΩ (nominal), < 100 pF Insulation resistance range : 0.01 MΩ to 2000 MΩ Test Voltage : 500 V, 1000V
	Specifications: Resistance measurement : 20Ω, 200Ω, 2KΩ, 20KΩ, 200KΩ, 2MΩ, 20MΩ Capacitance: 200pF, 2nF, 20nF, 200nF, 2µF, 20µF, 200µF, 2000µF Inductance: 200µH, 2mH, 20mH, 200mH, 2H, 20H, 200H
	Specifications: Two input and output HDMI ports 1Gbit (64MBx16) DDR2 128Mbit x4 quad SPI Flash Trimode (10/100/1000) Ethernet interface Audio codec with line in, line out, mic and headphone ports USB-USART and USB-HID host (for mice/keyboards) ports On-board USB-based FPGA configuration circuitry On board, real time power supply monitors